View 1PMT5300_1185100.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

8700 E. Thomas Road Scottsdale, AZ 85251 Tel: (480) 941-6300 Fax (480) 947-1503
1PMT5283 thru 1PMT5314
CURRENT REGULATOR DIODES
FEATURES:
* * * * * * * Surface-mount equivalent to 1N5283 thru 1N5314 series Popular Microsemi Powermite(R) surface-mount package Nominal current regulation from 0.22 and 4.70 mA Broad operating voltage Constructed with an Oxide Passivated All Diffused Die Full metallic bottom eliminates flux entrapment Integral Heat Sink Locking Tabs for excellent thermal dissipation and improved current regulation
MAXIMUM RATINGS:
* * * * Operating and Storage Temperature: -55C to +150C DC Power Dissipation: 600mW @ TL 135C Power Derating: 40mW/C @ TL > 135C Peak operating voltage: 100 Volts
D0-216
MECHANICAL CHARACTERISTICS
* * * * * * Terminals: Leads tin plated Thermal resistance: 30C/W junction to Tab 1 Polarity: Cathode indicated by a band Packaging: Tape and Reel (EIA Standard RS-481) Weight 0.016 gram Mounting position any way
PACKAGING
* * * Tape and Reel Standard 481 7 inch Reel 3,000 Pieces 13 inch Reel 12,000 Pieces
TYPICAL CURRENT REGULATOR CHARACTERISTICS 5.0 4.0 3.0 2.0 1.0 0 -20 -40 -60 -80 -100
-2.0 -1.0 0 Forwar POV
All dimensions +/- .005 inches/0.127mm
ZK @ V K IP & ZS @V
VL @ IL
Revers
Reverse Forward 20 40 60 Anode 80 90 Cathode 100 120 140
Mounting Pad Dimensions in Inches
VAK - ANODE CATHODE VOLTAGE (VOLTS)
ISO 9001 CERTIFIED
REV D 11/01/99
IPMT5283 thru IPMT5314 Electrical Characteristics @ TL=30C
REGULATOR CURRENT IP (mA)@ V S = 25V NOM 0.22 0.24 0.27 0.30 0.33 0.39 0.43 0.47 0.56 0.62 0.68 0.75 0.82 0.91 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.80 2.00 2.20 2.40 2.70 3.00 3.30 3.60 3.90 4.30 4.70 MIN 0.198 0.216 0.243 0.270 0.297 0.351 0.387 0.423 0.504 0.558 0.612 0.675 0.738 0.819 0.900 0.990 1.06 1.17 1.26 1.35 1.44 1.62 1.80 1.98 2.16 2.43 2.70 2.97 3.24 3.51 3.87 4.23 MAX 0.242 0.264 0.297 0.330 0.363 0.429 0.473 0.517 0.616 0.682 0.748 0.825 0.902 1.001 1.100 1.210 1.32 1.43 1.54 1.65 1.76 1.98 2.20 2.42 2.64 2.97 3.30 3.63 3.96 4.29 4.73 5.17 MINIMUM DYNAMIC IMPEDANCE @V S =25v ZS (M ) (NOTE 1) 25.0 19.0 14.0 9.0 6.6 4.10 3.30 2.70 1.90 1.55 1.35 1.15 1.00 0.880 0.800 0.700 0.640 0.580 O.540 0.510 0.475 0.420 0.395 0.370 0.345 0.320 0.300 0.280 0.265 0.255 0.245 0.235 MINIMUM KNEE IMPEDANCE @V K = 6.0V ZK (M ) (NOTE 2) 2.75 2.35 1.95 1.60 1.35 1.00 0.870 0.750 0.560 0.470 0.400 0.335 0.290 0.240 0.205 0.180 0.155 0.135 0.115 0.105 0.092 0.074 0.061 0.052 0.044 0.035 0.029 0.024 0.020 0.017 0.014 0.012 MAXIMUM LIMITING VOLTAGE @IL = 0.8 IP (min) V L (VOLTS) 1.00 1.00 1.00 1.00 1.00 1.05 1.05 1.05 1.10 1.13 1.15 1.20 1.25 1.29 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.75 1.85 1.95 2.00 2.15 2.25 2.35 2.50 2.60 2.75 2.90
PART NUMBER
1PMT5283 1PMT5284 1PMT5285 1PMT5286 1PMT5287 1PMT5288 1PMT5289 1PMT5290 1PMT5291 1PMT5292 1PMT5293 1PMT5294 1PMT5295 1PMT5296 1PMT5297 1PMT5298 1PMT5299 1PMT5300 1PMT5301 1PMT5302 1PMT5303 1PMT5304 1PMT5305 1PMT5306 1PMT5307 1PMT5308 1PMT5309 1PMT5310 1PMT5311 1PMT5312 1PMT5313 1PMT5314
NOTE 1: ZS is measured by superimposing a 90 Hz rms signal to 10% of VS on VS. NOTE 2: ZK is derived by superimposing a 90 Hz rms signal to 10% of VK on VK.
ISO 9001 CERTIFIED
REV D 11/01/99
IPMT5283 thru IPMT5314
Typical Forward Characteristics ID FORWARD DIODE CURRENT (mA)
10 7 5 3 2 1 1PMT5290 0.7 0.5 0.1 0.2 0.3 0.5 0.7 1.0 2.0 3.0 5.0 7.0 10.0 20 30 50 70 100 TJ = 25C VSM = 100V
(DATA OBTAINED FROM PULSE TESTING)
1PMT5313 1PMT5309 1PMT5305 1PMT5298
VAK ANODE- CATHODE VOLTAGE (VOLTS) Temperature Coefficient
0.7 0.6
IS - TEMPERATURE COEFFICIENT (%/C)
0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 0.2 0.3 0.4 0.5 0.7 1.0 2.0 Range Typical
TJ = +25C to +150C VAK = 25V A I P = ISI P(Nom) ATJ/100
3.0
4.0
5.0
IP NOMINAL PINCH-OFF CURRENT (mA) Temperature Coefficient
1.0 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 0.2 0.3 0.4 0.5 0.7 1.0 2.0 3.0 4.0 5.0 Range Typica TJ = -55C to +25C VAK = 25V A I P = ISI P(Nom) ATJ /100
IS - TEMPERATURE COEFFICIENT (%/C)
IP NOMINAL PINCH-OFF CURRENT (mA)
SYMBOLS AND DEFINITIONS
ID
IS
Ip POV VK VL VS ZK
ZS
Diode Current IL Limiting Current 80% of IP minimum used to determine Limiting Voltage, V L Current Temperature Coefficient. V AK anode to cathode Voltage Pinch-off Current: Regulator current at specified Test Voltage, V S . IP is some times identified as IS Peak Operating Voltage: Maximum voltage to be applied to the device. Knee Impedance test voltage: Specified voltage used to establish Knee Impedance Limiting Voltage: Measured at IL, V L, together with Knee ac Impedance, ZK , indicates the Knee characteristic of the device TEST VOLTAGE: Voltage at which IP and ZS are specified Knee ac impedance at Test Voltage: To test ZK a 90Hz signal V K with rms value equal to 10% of test voltage V K is superimposed on V K : ZK = V K /iK where iK is the resultant ac current due to v K . To provide the most constant current from the diode, ZK should be as high as possible, therefore, a minimum value of ZK is specified. AC Impedance at Test Voltage: Specified as a minimum value. To test for ZS , a 90 Hz signal V S with rms value equal to 10% of test voltage, V S is superimposed on V S : ZS = v S /iS where iS is the current due to v S .
ISO 9001 CERTIFIED
REV D 11/01/99
This datasheet has been download from: www..com Datasheets for electronics components.

▲Up To Search▲

Price & Availability of 1PMT5300

	To Download 1PMT5300 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .